- OSOYOO ESP8266 Wifi Module
- OSOYOO W5100 Ethernet IoT learning Kit
- OSOYOO Wifi IoT Learning Kit
- Smart House V2.0 Blynk Control
- Blynk IoT Learning Kit
- LoRa Related
- NodeMCU IoT Kit
- Smart Home Iot Kit
- Smart Home V2.0 UDP APP control
- Project for Raspberry Pi
- FlexiRover Robot Car for Raspberry Pi/Arduino
- IOT kit for raspberry Pi
- Mecanum Wheel Car
- OSOYOO basic kit for Raspberry pi zero
- OSOYOO Robot Car V1 for Raspberry Pi
- OSOYOO Robot Car V2 for Raspberry Pi
- OSOYOO Starter Kit V1 for Raspberry Pi
- OSOYOO Starter Kit V2 for Raspberry Pi
- Screen for Raspberry Pi
- Tank Car for Raspberry Pi
- OSOYOO V4.0 Robot Car for Raspberry Pi
- NodeMCU Garden Watering Kit
- OSOYOO 16+1 Sensor kit
- OSOYOO 3D Printer Kit
- OSOYOO Advanced Hardware Programming Learning Kit
- OSOYOO Basic Programming Learning Kit
- OSOYOO Cayenne IOT Learning Kit
- OSOYOO Graphical Programming Kit
- Osoyoo Hardware Programming Starter Kit
- OSOYOO IoT Smarthome Kit V0.1
- OSOYOO PNP Programming Learning Kit
- OSOYOO RFID Programming Learning Kit
- Osoyoo Sensor Modules Kit
- OSOYOO Sewing Programming Learning Kit
- OSOYOO Smart Home IoT Kit
- OSOYOO Ultimate Hardware Programming kit
- OSOYOO v3 advanced learning kits
- Balance car kit
- M1.0 Mecanum Wheel Metal Chassis Robotic
- M2.0 Mecanum Wheel Metal Chassis Robotic
- Mars Explorer Mecanum Wheel Robot Kit
- Tank Car Kit V1.0
- Tank Car Kit V2.0
- 2WD Robot Car Starter Kit
- Blue Acrylic Mecanum Wheel Robotic
- Model-3 V2.0 Robot Car
- OSOYOO Model-3 Robot Learning Kit
- OSOYOO Model-T Robot Car
- OSOYOO Robot Car Starter Kit Tutorial
- OSOYOO Servo Steering Car V3.0 for Arduino MEGA2560
- P3 Servo Steering Robot Car
- SG90 Servo Steering Robot Car
- V2.0 Robot Car kit
- V2.1 Robot car kit
Can you provide a pinout for the stepper motor connectors.
I forgot to say I have a MKS Base v1.5
I need the pinout for the MKS Base 1.5 For thermistors. I have downloaded your Firmware and Can’t get the second extruder to see the temp.
Do you config the Z anix according to the instruction?
Have a question. If I wanted to attach a BL Touch auto bed leveling probe, what pins would i attach the probe to for the MK SBASE v1.5 board? Just got the is board and would like to attach a auto bed leveling probe to it. Thank you very much in advance.
How do you access the I2C bus on the MKS gen 1.4?
hello …. i have 1 MKS BASE 1.5 i need help for configure marlin for the tronxy xy-08n sensor for my anet a8 please ?
HI, I’ve questions about the two extruders. Actually I’ve the MKS Base v1.4 powered with a 12VDC 20A Power supply. I’ve buy a second extruder and I’m concern about the power required and the actual power wires. There are already hot. Not at the point to melt, but there are hot.
So I’ve connect a 100A shunt with a DC power meter and found that my actual board power used is really near the maximum of my power supply (18.5A±1A). I’m wondering, if the actual board connector will be tough enough to support 2 extruders because, I will replace my actual 20A for a 40A (480W) Power supply.
How to connect endstops– The connectors on the MKS 1.5 board have 3 pins. The switches only have two pins. Which two pins on the connectors should be used?