Buy from US Buy from UK Buy from DE Buy from IT Buy from FR Buy from ES ここでご購入を!
  1. Introduction
  2. Preparation
  3. Library Installation
  4. MQTT Client Installation
  5. Upload sketch
  6. Configration of MQTT Client(MQTTBox)
  7. Program Running Result

Introduction

This lesson will show the basic MQTT protocol usage on the NodeMCU board.We use the MQTTBox as the MQTT client here, and we will use the NodeMCU to complete following  operations:

It will reconnect to the server if the connection is lost using a blocking reconnect function. See the ‘mqtt_reconnect_nonblocking’ example for how to achieve the same result without blocking the main loop.

Preparation:

Connect the NodeMCU to PC via USB cable.

Library Installation:

We need install MQTT endpoint library(PubSubClient) to communicate with MQTT broker,  please download the library from following link:

https://osoyoo.com/wp-content/uploads/samplecode/pubsubclient.zip

Unzip above file, move the unzipped folder to アルドゥイーノIDE library folder.

install lib

Open the アルドゥイーノIDE,you can find the “pubsubclient” on the “Examples” column:

example_pubsubclient

MQTT Client Installation:

In these lessons,we will use the MQTTBox as the MQTT client.(You can also use another client )

You will see this page after installation completed:

MQTTBOX

Upload sketch

If you completed all above operations,open アルドゥイーノIDE–>File–>Example–>pubsubclient–>mqtt esp8266,you will get below code:

upload sketch

Edit the code to fit your own WiFi and MQTT settings as following operations:

1)Hotspot Configration:

const char* ssid = “your_hotspot_ssid”;

const char* password = “your_hotspot_password”;

Find above code line,put your own ssid and password on there.

2)MQTT  Server  Address Setting

const char* mqtt_server = “broker.mqtt-dashboard.com”;

You can use your own MQTT broker URL or IP address to set above mqtt_server value. You can also use some famous free MQTT server to test the project such as  “broker.mqtt-dashboard.com”,  “iot.eclipse.org” etc.

3)MQTT Client Settings

If your MQTT broker require clientID,username and password authentication,you need to change

if (client.connect(clientId.c_str()))

to

if (client.connect(clientId,userName,passWord)) //put your clientId/userName/passWord here

If not,just keep them as default.

After do that,choose the coresponding board type and port type as below,then upload the sketch to the NodeMCU.

board port settings

Configration of MQTT Client (MQTTBOX)

In this step,we will show how to create an MQTT client on the MQTTBox.

Open your MQTTBox and click the blue button to add a new MQTT client.

create mqtt client

Then you will see:

MQTTBOX2

Config the MQTT CLIENT SETTINGS as below:

Click to save your changes.

boxsettings

Next, you will automatically enter the new page.If all above configration is correct,the “Not Connected” will change to “Connected” ,your MQTT client name and Host name will be displayed at the top of this page.

pub sub

Topic setting:

Make sure your MQTT client publish topic is same as your アルドゥイーノsketch subscribe topic(inTopic here).

Make sure your MQTT client subscribe topic is same as your アルドゥイーノsketch publish topic(outTopic here).

Sketch side:

Program Running Result:

Onece the upload done,if the wifi hotspot name and password setting is ok, and MQTT broker is connected, open the Serial Monitor,you will see following result:

serial result

You can see the publish message “hello world” on the serial monitor.Then open the MQTT client and publish payload “1” to the topic, this NodeMCU will recevie these messages by subscribing to the “inTopic”,and the LED will be lit.

IMG_20170511_175505

Publish payload “0” to this topic,the NodeMCU LED will be turned off.

IMG_20170511_175535

As shown in the right figure below,once click the Subscribe button of  this subscribe topic,this topic will keep subscribe to the messages that published by this NodeMCU.

box pubsub