Buy from US	Buy from UK	Buy from DE	Buy from FR	Buy from IT	Buy from ES	ここでご購入を！

In this lesson, we will show you how to make use Internet to monitor remote motion sensor status and detect intruder.

We  will  use  Osoyoo Mega-IoT Shield  to connect motion Sensor(photoresistor), LEDs and MEGA2560 MCU board.  OSOYOO Advanced Board for Arduino MEGA2560 can work as a web server. Remote browser can access this web server  to shows motion sensor real time status.

OSOYOO Advanced Board for Arduino MEGA2560 x 1
OSOYOO MEGA-IoT extension board x 1
USB Cable x 1
Red LED PnP module x 1
Green LED PnP module x 1
motion Sensor(Photoresistor) PnP module x 1
Buzzer module x 1
PnP cable x 4

First, please plug OSOYOO MEGA-IoT Extension Board into OSOYOO Advanced Board for Arduino MEGA2560:

Then connect the modules with the OSOYOO MEGA-IoT Extension Board with four 3-pin PnP cables as below：

(Jumper Cap should connect ESP8266 RX with A8, TX with A9)

Green LED Module – D12

Red LED Module – D11

Buzzer Module – D5

motion Sensor-D4

Notice: Shut off your battery or Unplug your power adapter when upload sketch code to OSOYOO Advanced Board for Arduino MEGA2560.

Step 1 Install latest IDE (If you have IDE version after 1.1.16, please skip this step)
Download IDE from https://www.arduino.cc/en/software, then install the software.

Step 2 WifiEsp Library Installation (if you have installed WifiESP library, please skip this step)

OSOYOO MEGA-IoT extension TX/RX pin to OSOYOO Advanced Board for Arduino MEGA2560 A9/A8 pin by default. So in sketch code, we need use Software Serial Port to communicate with ESP8266 (set A9 as TX and A8 as RX in softwareserial object).

To use this wifi shield in IDE, we need download WiFiEsp-master library from following link:
https://osoyoo.com/driver/WiFiEsp-master.zip

Open IDE,  click Sketch – Include Library- Add .Zip library to load above zip files into IDE.

Step 3 After installing above library, please download the main code from following link, unzip it, you will see a folder called “smarthome-lesson13”:

https://osoyoo.com/driver/smarthome/smarthome-lesson13.zip

Step 4 After above operations are completed, connect OSOYOO MEGA2560 Board to PC with USB cable.

Step 5 IDE:  Choose corresponding board type and port type for you project .

Step 6 IDE:  Click file – Open, then choose code “smarthome-lesson13.ino” in the folder, load up the  sketch onto your OSOYOO Advanced Board for Arduino MEGA2560.

Note: In the  sketch, find  line 24，25 as following:

char ssid[] = "******"; // your network SSID (name)
char pass[] = "******"; // your network password

please replace the ****** with your correct wifi SSID and password, otherwise your project can not connect to Internet.

After loading the sketch to OSOYOO Advanced Board for Arduino MEGA2560 , open the serial monitor in the upper-right corner of  IDE, you will see following result:

From the serial monitor ,  you can see the IP address of your MEGA2560 board in the read circle (in above picture, 192.168.50.102).

Then use your browser to visit the website http://mega2560-ip-address (in above case, http://192.168.50.102), you will see following result:

Above result means there is no intruder (motion signal) is detected. The Red LED on the D13 pin of MEGA-IoT shield is off and Green LED is ON which shows the same result.

Now put your hand close to motion sensor, You will see the Green LED on IoT shield will be off and Red LED will turn ON, buzzer will alarm.

Now check the web browser , after about 2 to 5 seconds, the browser will show following result.