In this lesson, we will show how to check the tilt sensor values on NodeMCU, then send these values to the OSOYOO IoT APP, so we can use the APP to get these values remotely, then determine whether the object is tilted .
This SW-520D basic tilt switch can easily be used to detect orientation. Inside the can is a ball that make contact with the pins when the case is upright. Tilt the case over and the balls don’t touch, thus not making a connection.
There are numerous uses for these basic sensors, but keep in mind you might need to use some debouncing code, as the sensor isn’t immune to small vibrations and such.
Overhere,we use A0 as the analog input pin.
Connect the NodeMCU to computer via USB cable,open this sketch by using Arduino IDE(Version1.6.4+):
Edit the code to fit your own WiFi settings as following operations:
#define STASSID “***” // replace *** with your wifi SSID
#define STAPSK “***” // replace *** with your wifi password
Find above code line,put your own ssid and password on there.
2)UDP local port Settings
// Define the local port to listen on
unsigned int localPort = 8888;
We use the “8888” local port here, you can change it to your own local port.
3)Boad & COM Port Settings
After do that,choose the coresponding board type and port type as below,then upload the sketch to the NodeMCU.
About how to config the UDP APP,check this link.
Click the setting icon button, you can see the UDP configration page.
UDP response text display enable button – Enable text play
UDP Incoming Port – Use this port to listen for and accept connections from remote UDP devices, keep the default setting : “8888”
IP address – Change it to your NodeMCU IP address, you can get the IP address from the Arduino IDE Serial Monitor after the code upload down.
Port – Keep the default setting: “8888”.
Keep other settings as default, then click the “Save” button to save your changes.
Upload the code to Arduino board, then open Arduino Serial monitor in the upper right corner.
Now please set your Baud Rate to 115200
you will see NodeMCU IP address as following:
Above result shows your NodeMCU IP address (in my case, 192.168.0.19) , NodeMCU is now waiting for UDP message at port 8888.
Onece the upload done,if wifi hotspot name and password setting is ok and UDP APP is connected, open the Serial Monitor, when you put down the tilt sensor linked to A0, you can see a corresponding value:
At the same time,open the UDP APP ,press any function button on the APP,
You will see the Real time tilt sensor status as below:
When the tilt sensor is in the vertical position, you can see that：
And the APP side as below:
Question A: Why could OSOYOO IoT APP send message to NodeMCU without even knowing the IP address of the NodeMCU board?
Answer: OSOYOO IoT APP default destination IP is 192.168.1.255 which is a broadcasting IP address. Broadcasting means the APP will send UDP message to all device in the same Wifi Network.
So even we does not set destination IP address to NodeMCU IP, the NodeMCU can still get the message.
Question B: Can I change default sending destination IP address and Port Number of OSOYOO IoT APP?
Yes, you can! Osoyoo IoT APP default IP is 192.168.1.255 and default port is 8888. If you need to change the setting,
For example, if our NodeMCU IP address is 192.168.0.8, here is the guide to make the change to 192.168.0.8:
1)Open APP, click Setting button in upper right corner
2)Use 192.168.0.8 to replace default IP 192.168.1.255
3)keep default port number 8888 without changing
4)turn on the switch of UDP Response Text Display
5)Click Save button to save the changes you just made
6)Click Back Arrow to go back APP front UI
Question A: I touched my APP F1 key, but no message shows up in my NodeMCU serial monitor, why?
Sometimes, broadcasting IP Address is not necessarily 192.168.1.255, for example, if your NodeMCU IP address is 192.168.0.8, the wifi network broadcasting IP is 192.168.0.255.
So we suggest you replace 192.168.1.255 with 192.168.0.255 to match your network mask of NodeMCU. Of course you can directly set the NodeMCU IP as destination in APP.
If you have any question about OSOYOO NodeMCU products, feel free to contact us or leave comments here.
In next lesson, we will connect a sensor to NodeMCU and send sensor data to another Moquitto client software.
We need to note that ESP8266 is a 2.4G WiFi device, please access to 2.4G network, if you access to a 5G router network, there will be a prompt that the network connection is not successful.
|1||OSOYOO NodeMCU Board||https://osoyoo.store/products/osoyoo-nodemcu-module-usb-c-esp8266-esp-12f-wifi-development-board-with-ch340-for-arduino-ide-micropython-includes-tutorial?variant=41099777638511|
|3||LED(6 x White, 6 x Red, 6 x Yellow, 6x Green)||https://osoyoo.store/products/led-packs-for-arduino?variant=31957816442991|
|5||Push Button and Hats||https://osoyoo.store/products/push-button-and-hats-5pcs?variant=39879253131375|
|7||potentiometer(10K lohm adjustable resistor)||https://osoyoo.store/products/potentionmeter-10k-adjustable-resistor-3pcs?variant=39879281016943|
|8||I2C LCD Display (16*2)||https://osoyoo.store/products/i2c-1602-lcd-display-module-blue-backlight?variant=41099777933423|
|9||Temperature&Humidity Sensor Module||https://osoyoo.store/products/dht11-temperature-humidity-sensor?variant=41099777998959|
|11||4*AA Battery Holder Box||https://osoyoo.store/products/battery-box-for-4pcs-aaa-battery?variant=41099778031727|
|12||4 LED Module||https://osoyoo.store/products/4-digit-7-segment-display?variant=41099778064495|
|13||Stepper Motor +Bridge||https://osoyoo.store/products/stepper-motor-with-driver-28byj-48-5v-dc?variant=41099778130031|
|14||Tlit Sensor Module||https://osoyoo.store/products/sw-520d-basic-tilt-switch?variant=41099778162799|
|15||Infrared Remote Controller||https://osoyoo.store/products/infrared-remote-controller-for-arduino-raspberry-pi-microbit-stemmodel-2019011500?variant=31958087532655|
DownLoad Url osoyoo.com