(DKHK100200)Lesson16-Two-way relay module for arduino

Content

  1. Introduction
  2. Preparations
  3. About the 2-Channel Relay Module
  4. Example
  5. Connection
  6. Upload Sketch
  7. Program Running Result

Introduction

A relay is an electrically operated switch. Many relays use an electromagnet to mechanically operate a switch, but other operating principles are also used, such as solid-state relays. Relays are used where it is necessary to control a circuit by a separate low-power signal, or where several circuits must be controlled by one signal.

In this lesson, we will show you how the 2-Channel Relay Module works and how to use it with the Osoyoo Uno board to control high voltage devices.

Preparations

Hardware

Software

About 2-Channel Relay Module

Overview

This is a 5V 2-Channel Relay Module board, Be able to control various appliances, and other equipment with large current. It can be controlled directly by Microcontroller (Raspberry Pi, Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic). Very useful project for application like Micro-Controller based projects, Remote controller, Lamp on Off, and any circuits which required isolated high current and high voltage switching by applying any TTL or CMOS level voltage.

Features

Pins Out

Input

It has a 1×4 (2.54mm pitch) pin header for connecting power (5V and 0V), and for controlling the 2 relays. The pins are marked on the PCB:

There is a second 1×3 (2.54mm pitch) pin header for supplying the “relay side” of the board with 5V. At delivery, a jumper is present on this header selecting the 5V signal from the 1×4 pin header to power the relays. For default operation, don’t change this jumper!

The pins of the 1×3 pin header are marked on the PCB:

If opto isolation is required, an isolated 5V supply should be used. For normal operation, a jumper bewtween pins 1 and 2 selects the 5V signal from the 1×4 pin header. This means both the “input side”, and “relay side” use the same 5V supply, and there is no opto-isolation.

Output

The 2 channel relay module could be considered like a series switches: 2 normally Open (NO), 2 normally closed (NC) and 2 common Pins (COM).

Schematic

How relay works?

The working of a relay can be better understood by explaining the following diagram given below.

There are 5 parts in every relay:

1. Electromagnet – It consists of an iron core wounded by coil of wires. When electricity is passed through, it becomes magnetic. Therefore, it is called electromagnet.

2. Armature – The movable magnetic strip is known as armature. When current flows through them, the coil is it energized thus producing a magnetic field which is used to make or break the normally open (N/O) or normally close (N/C) points. And the armature can be moved with direct current (DC) as well as alternating current (AC).

3. Spring – When no currents flow through the coil on the electromagnet, the spring pulls the armature away so the circuit cannot be completed.

4. Set of electrical contacts – There are two contact points:

.Normally open – connected when the relay is activated, and disconnected when it is inactive.

.Normally close – not connected when the relay is activated, and connected when it is inactive.

5. Molded frame – Relays are covered with plastic for protection.

Principle

The diagram shows an inner section diagram of a relay. An iron core is surrounded by a control coil. As shown, the power source is given to the electromagnet through a control switch and through contacts to the load. When current starts flowing through the control coil, the electromagnet starts energizing and thus intensifies the magnetic field. Thus the upper contact arm starts to be attracted to the lower fixed arm and thus closes the contacts causing a short circuit for the power to the load. On the other hand, if the relay was already de-energized when the contacts were closed, then the contact move oppositely and make an open circuit.

As soon as the coil current is off, the movable armature will be returned by a force back to its initial position. This force will be almost equal to half the strength of the magnetic force. This force is mainly provided by two factors. They are the spring and also gravity.

Relays are mainly made for two basic operations. One is low voltage application and the other is high voltage. For low voltage applications, more preference will be given to reduce the noise of the whole circuit. For high voltage applications, they are mainly designed to reduce a phenomenon called arcing.

High Voltage Warning


Before we continue with this lesson, I will warn you here that we will use High Voltage which if incorrectly or improperly used could result in serious injuries or death. So be very caution of what you are doing.

Examples

Using the Arduino to Control a 2 Channel Relay

In this example, when a low level is supplied to signal terminal of the 2-channel relay, the LED on the relay will light up. Otherwise, it will turn off. If a periodic high and low level is supplied to the signal terminal, you can see the LED will cycle between on and off.

Connection

Build the circuit as below digram:

Code Program

After above operations are completed, connect the Arduino board to your computer using the USB cable. The green power LED (labelled PWR) should go on.Open the Arduino IDE and choose corresponding board type and port type for you project. Then load up the following sketch onto your Arduino.

//the relays connect to int IN1 = 2; int IN2 = 3; #define ON 0 #define OFF 1 void setup() { relay_init();//initialize the relay } void loop() { relay_SetStatus(ON, OFF);//turn on RELAY_1 delay(2000);//delay 2s relay_SetStatus(OFF, ON);//turn on RELAY_2 delay(2000);//delay 2s } void relay_init(void)//initialize the relay { //set all the relays OUTPUT pinMode(IN1, OUTPUT); pinMode(IN2, OUTPUT); relay_SetStatus(OFF, OFF); //turn off all the relay } //set the status of relays void relay_SetStatus( unsigned char status_1, unsigned char status_2) { digitalWrite(IN1, status_1); digitalWrite(IN2, status_2); }

Running Result

A few seconds after the upload finishes, you should see the LED cycle between on and off.