Buy from US Buy from UK Buy from DE Buy from FR Buy from IT Buy from ES ここでご購入を！

In this lesson, we will show you how to make use Internet to monitor remote Fire Sensor status.

We  will  use  Osoyoo Mega-IoT Shield  to connect Fire Sensor, LEDs and MEGA2560 MCU board.  OSOYOO Advanced Board for Arduino MEGA2560 can work as a web server. Remote browser can access this web server  to shows fire sensor real time status.

HARDWARE

First, please plug OSOYOO MEGA-IoT Extension Board into OSOYOO Advanced Board for Arduino MEGA2560:

Then connect the modules with the OSOYOO MEGA-IoT Extension Board with four 3-pin PnP cables as below

(Jumper Cap should connect ESP8266 RX with A8, TX with A9):

Green LED Module – D12

Red LED Module – D11

Buzzer Module – D5

Flame Detection Sensor – A1

Notice: Shut off your battery or Unplug your power adapter when upload sketch code to OSOYOO Advanced Board for Arduino MEGA2560.

Step 1 Install latest IDE (If you have IDE version after 1.1.16, please skip this step)
Download IDE from https://www.arduino.cc/en/software , then install the software.

Step 2 WifiEsp Library Installation (if you have installed WifiESP library, please skip this step)

OSOYOO MEGA-IoT extension TX/RX pin to OSOYOO Advanced Board for Arduino MEGA2560 A9/A8 pin by default. So in sketch code, we need use Software Serial Port to communicate with ESP8266 (set A9 as RX and A8 as TX in softwareserial object).

To use this wifi shield in IDE, we need download WiFiEsp-master library from following link:
https://osoyoo.com/driver/WiFiEsp-master.zip

Open IDE,  click Sketch – Include Library- Add .Zip library to load above zip files into IDE.

Step 3 After installing above library, please download the main code from following link, unzip it, you will see a folder called “smarthome-lesson10”:

https://osoyoo.com/driver/smarthome/smarthome-lesson10.zip

Step 4 After above operations are completed, connect OSOYOO MEGA2560 Board to PC with USB cable.

Step 5 IDE:  Choose corresponding board type and port type for you project .

Step 6 IDE:  Click file – Open, then choose code “smarthome-lesson10.ino” in the folder, load up the  sketch onto your OSOYOO Advanced Board for Arduino MEGA2560.

Note: In the  sketch, find  line 24，25 as following:

char ssid[] = "******"; // your network SSID (name)
char pass[] = "******"; // your network password

please replace the ****** with your correct wifi SSID and password, otherwise your project can not connect to Internet.

Notice: Please use the Philips Screwdriver to adjust the Flame Detection Module’s sensitivity by adjusting the potentiometer, when there’s no fire, you should adjust the module to the green light.

After loading the sketch to OSOYOO Advanced Board for Arduino MEGA2560, open the serial monitor in the upper-right corner of IDE, you will see following result:

From the serial monitor ,  you can see the IP address of your MEGA2560 board in the read circle (in above picture, 192.168.50.102).

Then use your browser to visit the website http://mega2560-ip-address (in above case, http://192.168.50.102), you will see following result:

Above result means there is no Fire signal is detected. The Red LED on the D12 pin of MEGA-IoT shield is off and Green LED is ON which shows the same result.

Now let’s use a gas lighter to turn a small flame, the gas flame will trig some IR signal to sensor. You will see the Green LED on IoT shield will be off and Red LED will turn ON, buzzer will alarm.

Now check the web browser , after about 2 to 5 seconds, the browser will show following result: