You can download the user manual from:
|1||Wooden House Model||1||Click here to buy|
|2||OSOYOO Advanced Board for Arduino MEGA2560
(Fully compatiable with Arduino Mega2560)
|1||Click here to buy|
|3||OSOYOO MEGA-IoT Extension Board||1||Click here to buy|
|4||Photosensitive Sensor||1||Click here to buy|
|5||Temp & Hum Sensor||1||Click here to buy|
|6||OSOYOO Active Buzzer Module||1||Click here to buy|
|7||Flame Detection Sensor||1||Click here to buy|
|8||1-Channel Relay||1||Click here to buy|
|9||Micro Servo Motor||1||Click here to buy|
|10||RGB Module||1||Click here to buy|
|11||Ultrasonic Sensor||1||Click here to buy|
|12||PIR Motion Sensor||1||Click here to buy|
|13||Microphone Module||1||Click here to buy|
|14||1602 I2C LCD Screen||1||Click here to buy|
|15||Gas Detection Module||1||Click here to buy|
|16||RFID Module||1||Click here to buy|
|17||4*4 Keypad||1||Click here to buy|
|18||Yellow LED Module||1||Click here to buy|
|19||Red LED Module||1||Click here to buy|
|20||Green LED Module||1||Click here to buy|
|21||White LED Module||1||Click here to buy|
|22||Red Button Module||1||Click here to buy|
|23||Blue Button Module||1||Click here to buy|
|24||Philips Screwdriver||1||Click here to buy|
DownLoad Url osoyoo.com
You must be logged in to post a comment.
Would like to buy.Please guide me throughout.
Hi, you can buy it from this link:
how to buy?
Hi, you can buy it from Amazon:
If you’re in Europe, you can search B07DW3GRHM
Hi, I recently purchased this and it came with a CD with this webpage printed on it. I don’t have a CD drive so I was hoping to download an instructional pdf from this website but I can’t find it? I also cannot download the pdf from the QR code?
Hi, I’m sorry for your inconvenience, you can download it from this website:
I bought 2 weeks ago the OSOYOO Yun IoT Smart Home Kit and I still have the same problem whatever I did!
I try to control a LED via Blink by following this tutorial :
I’ve got this 2 errors :
1) On blink : “blink not online yet”
2) On the serial monitor : “Impossible to connect” and “Does the sketch use the bridge?”
Any advices to progress about this problem would be helpfull !
Hi, could you please take a picture to show the products? As this kit has two version, I’d like to know which version of yours is.
Of course ! This is the picture mo my kit.
It is a network link problem. If there is a problem with the network connection settings? Is the ssid and password correct? Please refer to the following picture.
I suppose it’s not a network link problem because I managed to connecte to the draguino interface as you can see :
Do you confirm it’s ok ?
I followed step by step the tutorial you mentionned.
Hi, could you please follow this tutorial to confirm if yun shield is connected to the internet?
The tutorial: https://osoyoo.com/2018/02/05/osoyoo-yun-iot-led-blink/
I finally found the reason it didn’t work..In IDE I used Arduino Yun board card,instead of “Arduino Mega 2560 – Dragino Yun” , and now it works !
Many thanks for your help.
Glad to hear that, if there’s anuything I can help, please feel free to tell me.
How can I buy one more yun iot.extension board and osoyoo mega 2560 board?
Hi, do you mean this extension board:
no, it should be the board for the smart home
I also want to but the mego 2560 too
Hi, you can buy from: https://www.amazon.com/dp/B083K263NB
Would it be possible to buy on aliexpress for the same price as amazon? I’m in Brazil and that would greatly simplify shipping, but the price is more than double.
Hi, I’m sorry that we can’t ship it in current
Hi, you can visit : https://www.aliexpress.com/item/32904777146.html?spm=a2g0s.122695220.127.116.11a65cb3J7tk6t to buy it.
Hi, I would get tutorials of 4*4 Keyboard and smart home system on OSOYOO Smart Home IoT Learning Kit with MEGA2560.
I got the information about yun iot.extension board, but I could find that on this kit….
I have completed my evaluation of this kit. I purchased this with the intention of giving it to my nephew to gain experience with the Internet of Things. I am going to request a return to Amazon because I believe it would be frustrating for him because in the first sensor experiment, Lesson 4, I found that the port D13 is faulty and so the LED will not light. The port has power between Vcc and GND, but apparently the SIG is not working. In later lessons, the same LED is hooked up to port D11, and in that case, the LED works as expected. Additionally, port D12 works intermittently. Sometimes, when running the program, and LED connected to port D12 will not light as expected, but then while the program continues to run, it will start working and then stop. I would recommend some consistency in the illustrations for sensor switch positions. For example, Lesson 9 specifies that the gas detector switch be selected to “D” on the left and shows the switch in gray. However, in following lessons, the convention is reversed and the switch on the left appears in black. Also, Lesson 10 gives the hint that the potentiometer may have to be adjusted to get the expected sensor response. This note probably should appear in other lessons using sensors which have potentiometers.
Our purpose of designing this kit is for people to better learn and understand the Internet of Things and sensors. We made the sensor a plug-and-play way to save the user’s hardware connection time. If you encounter problems during the use of our products For questions, you can directly contact our customer service or technical support. But we encourage ourselves to explore and think about more creative and interesting things with our hearts
Since today, I’ve got this message when i try to compil on my IDE 1.8.12:
fatal error: pins_arduino.h: No such file or directory
exit status 1
Error compiling for board Dragino Yún + Mega 2560.
I tried to update my IDE to 1.8.12, but the problem is still the same…
Many thanks in advance.
Could you give me the code? Or more details about your projects.
Of course, that’s the lesson 9 “Control a LED Blink(Blynk)”
#define BLYNK_PRINT Console
// You should get Auth Token in the Blynk App.
// Go to the Project Settings (nut icon).
char auth = “Your Auth Token”;
// Debug console
// You can also specify server:
//Blynk.begin(auth, “blynk-cloud.com”, 8442);
//Blynk.begin(auth, IPAddress(192,168,1,100), 8442);
// You can inject your own code or combine it with other sketches.
// Check other examples on how to communicate with Blynk. Remember
// to avoid delay() function!
Actually, even with only this small part of program I’ve got the same problem…
The code you used is applicable to the OSOYOO Yun IOT KIT. Now the OSOYOO smart home IOT learning kit uses the mega IOT expansion board based on esp8266. Here, we do not use the code related to Blynk.